Miller Electric Remote Operator Interface Bedienungsanleitung PDF herunterladen (Seite 5)

MILLER ELECTRIC MFG. CO., APPLETON, WI

MADE IN

Control Panels

1.Power Switch

2.Handheld

RS-232 Port

3.PC-Communication

RS-232 Port

4.115 VAC, 10 A

Duplex Receptacle

5.Circuit Breakers

6.Network Feeder

Connector

1. Voltage/Arc Adjust

Display Meter

2. Program Display

3. Program # Select

4. Process Setup Button

5. Control Knob

6. Trigger Receptacle

7. On/Off Button

8. Voltage Setup Button

9. Wire Speed Setup

Button

10. Wire Speed/Amperage

Display Meter

11. Feeder Setup Button

12. Jog/Purge Switch

Front Panel

Rear Panel

Program

Process

Wire Type

Gas Type

Volts Time Arc Adjust

WFS Amps Arc Ctl

Process Set Up

Adjust

Feeder Set Up

Trigger Hold

Trigger Control

Sequence

Single Axcess Feeder and

Remote Operator Interface (ROI)

Capabilities

Dual Schedule— Toggle between two

settings using a single wire.

4T— When trigger is released, output will

operate at different ranges.

Trigger Program Select (TPS)— Provides

the ability to “Axcess” any of the Multi-MIG

processes or any of the eight active programs.

Trigger Dual Schedule (TDS)— When activated

allow selection between predetermined program

pairs (e.g. 1,2 – 3,4 – 5,6 – 7,8).

Trigger Hold (TH)— When activated, allows

gun trigger release and continuous welding until

trigger is pulled again.

Carbon Arc Gouging (CAC-A)—Can be activated.

Wire Size

.023/.025 in (0.6 mm) #151 024 — — —

.030 in (0.8 mm) #151 025 — — —

.035 in (0.9 mm) #151 026 #243 233 #151 052 —

.040 in (1.0 mm) #161 190 — — —

.045 in (1.1/1.2 mm) #151 027 #243 234* #151 053 #151 070

.052 in (1.3/1.4 mm) #151 028 #151 038 #151 054 #151 071

1/16 in (1.6 mm) #151 029 #243 235 #151 055 #151 072

.068/.072 in (1.8 mm) — — #151 056 —

5/64 in (2.0 mm) — #151 040 #151 057 #151 073

3/32 in (2.4 mm) — #151 041 #151 058 #151 074

7/64 in (2.8 mm) — #151 042 #151 059 #151 075

1/8 in (3.2 mm) — #151 043** #151 060** #151 076**

Drive Roll Kits and Guides

(Order from Miller Service Parts.)

Drive Roll Kits

Select drive roll kits from chart below according to type and wire size being used.

Drive roll kits include 4 drive rolls, the necessary guides and feature an anti-wear sleeve for inlet guide.

*Accommodates .045 and .047 (3/64 in) wire. **May require a low-speed, wire-feed drive-roll option.

“V” groove

for hard wire

“U” groove for soft

wire or soft-shelled

cored wires

“V” knurled for

hard-shelled

cored wires

“U” cogged for

extremely soft wire or

soft-shelled cored wires

(i.e., hard facing types)

Intermediate

Wire Size Inlet Guide Guide

.035 in (0.9 mm) #221 912 #242 417

.047 in (1.2 mm) #221 912 #205 936

1/16 in (1.6 mm) #221 912 #205 937

Nylon Wire Guides for

Feeding Aluminum Wire

Intermediate

Wire Size Inlet Guide Guide

.023–.040 in #150 993 #149 518

(0.6–1.0 mm)

.045–.052 in #150 994 #149 519

(1.1–1.4 mm)

1/16– 5/64 in #150 995 #149 520

(1.6– 2 mm)

3/32–7/64 in #150 996 #149 521

(2.4– 2.8 mm)

1/8 in (3.2 mm) #150 997 #149 522

Note: “U” groove drive rolls are recommended when

feeding aluminum wire.

Wire Guides

Crater: 0.1–5 s

Postflow: 0.1–5 s

Sequence (in seconds)

Preflow: 0.1–5 s

Start Power: 0.1–5 s

Arc Adjust— Arc length (Trim)

Arc Control— Arc force or focus (SharpArc

)

Process Selection— Accu-Pulse

, Pulsed MIG,

MIG, Metal Core, RMD

™

(Optional)

1 2 3 4 5 6

Kommentare zu diesen Handbüchern

Keine Kommentare

Miller Electric Remote Operator Interface Bedienungsanleitung Seite 5

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Vernetzung Miller Electric Remote Operator Interface